Cable management in the server rack
horizontal & vertical

Cable management panels, cable guide rings in seven sizes, brush panels and vertical ducts up to 47 U — the complete cable management for SZB IT and other 19″ cabinets, with dimensions and catalogue numbers.

Request a quote Configure a cabinet with accessories

Order in two directions

Cable management in a server rack has two axes: horizontally, cable management panels guide the patch cables from the equipment front to the side; vertically, ducts and trays carry the bundles up to the cable entry in the roof or down into the raised floor. If you keep the two cleanly separated, you will still find every cable after the third refit — and keep the airflow in front of and behind the equipment clear.

Cable management panels: horizontal routing

The cable management panel sits between the patch panels and takes up the cable reserve. Three designs are available: with cable duct and removable front cover (closed look, cables hidden), with open rings (quick re-patching) and as a panel for cable guide rings, which you fit yourself with steel rings in the right size.

Cable management panel with cable duct, 1 U – removable front, cut-outs top and bottom
Cable management panel with cable duct, 1 Uremovable front, cut-outs top and bottom
Cable management panel with cable duct, 2 U – for high port densities
Cable management panel with cable duct, 2 Ufor high port densities
Cable management panel with 5 rings – rings made of black plastic
Cable management panel with 5 ringsrings made of black plastic
Cable management panel with brush seal – 5 rings, 4 cable cut-outs with brush
Cable management panel with brush seal5 rings, 4 cable cut-outs with brush

Cable management panels with cable duct (width 483 mm, RAL 9005)

HeightDepthCut-outs top/bottomCut-out widthMaterialCatalogue number
1 U87 mm1215 mmPlasticT-SO-900-614
2 U87 mm1215 mmPlasticT-SO-900-615
1 U174 mm12 + 1215 mmPlasticT-SO-900-618
1 U71 mm1210 mmsheet steelT-SO-900-613
1 U48 mm246 mmsheet steelT-SO-900-616

Two cable cut-outs at the rear, removable front cover. Supplied without fixing accessories, packaging unit 1 pc.

Cable management panels with rings (1 U, width 483 mm)

VersionDepthRingsCatalogue number
with rings90 mm5T-SO-900-617
with rings and 4 cut-outs with brush seal75 mm5T-SO-900-008
with rings, high density80 mm9WNK-811-000

Panel made of powder-coated sheet steel, rings made of black plastic. Supplied without fixing accessories.

Request with the enclosure →or individually for retrofitting

Cable guide rings and cable guide bar

The galvanised cable guide rings are the most flexible element: they are bolted to the cable management panel W-SB55 or directly to the 19″ profile rails — which also creates a vertical guide on the rail without an additional duct. Three ring shapes, seven sizes each, in sets of 5 including fixings; black (RAL 9005) on request. The cable guide bar, by contrast, runs in the depth direction: between the front and rear profile rails, parallel to the side panel, for tying down whole bundles.

Ring W-SB52 – galvanised steel, set of 5
Ring W-SB52galvanised steel, set of 5
Ring W-SB53 – galvanised steel, set of 5
Ring W-SB53galvanised steel, set of 5
Ring W-SB54 – galvanised steel, set of 5
Ring W-SB54galvanised steel, set of 5
Rings on cable management panel W-SB55 – 1 U, 8 rubber blanking plugs for free openings
Rings on cable management panel W-SB551 U, 8 rubber blanking plugs for free openings
Size A × BShape W-SB52Shape W-SB53Shape W-SB54
88 × 88 mmW-SB52-00-01-000W-SB53-00-01-000W-SB54-00-01-000
66 × 88 mmW-SB52-00-02-000W-SB53-00-02-000W-SB54-00-02-000
66 × 66 mmW-SB52-00-03-000W-SB53-00-03-000W-SB54-00-03-000
44 × 110 mmW-SB52-00-04-000W-SB53-00-04-000W-SB54-00-04-000
44 × 88 mmW-SB52-00-05-000W-SB53-00-05-000W-SB54-00-05-000
44 × 66 mmW-SB52-00-06-000W-SB53-00-06-000W-SB54-00-06-000
44 × 44 mmW-SB52-00-07-000W-SB53-00-07-000W-SB54-00-07-000

Packaging: set of 5 with fixing accessories. Black version (RAL 9005) on request.

Cable management panel for cable guide rings (1 U)

VersionRAL 7035RAL 9005
Cable management panel without rings, with 8 rubber blanking plugsW-SB55-00-00-011W-SB55-00-00-161

Order rings separately.

Cable guide bar (galvanised steel, holes for M6)

LengthCatalogue number
210 mmW-SB00-29-05-000
310 mmW-SB00-29-04-000
335 mmW-SB00-29-03-000
410 mmW-SB00-29-02-000
500 mmW-SB00-29-01-000

Supplied with fixing accessories, packaging unit 1 pc.

Request with the enclosure →or individually for retrofitting

Brush panels: through the 19″ level, without air leakage

Where cables pass from the front to the rear, a hole quickly appears through which warm air flows back into the cold zone. The brush panel closes this opening: a cable pass-through of 341 × 21.5 mm with brush seal, 1 U high. The version with support plate (300 mm deep) also takes up cable reserves.

Brush panel without support plate – 1 U, depth 50 mm
Brush panel without support plate1 U, depth 50 mm
Brush panel with support plate – 1 U, depth 300 mm, for cable reserves
Brush panel with support plate1 U, depth 300 mm, for cable reserves
VersionDepthRAL 7035RAL 9005
without support plate50 mmW-SB63-00-01-011W-SB63-00-01-161
with support plate300 mmW-SB63-00-02-011W-SB63-00-02-161

Cable pass-through 341 × 21.5 mm with brush seal. Supplied with fixing accessories, packaging unit 1 pc.

Matching items: plates with brush pass-through for floor and roof plate, and horizontal brushes for the cabinet front — see Blanking & covers.

Request with the enclosure →or individually for retrofitting

Vertical cable routing

For vertical routing in the side space there are four solutions — the choice depends mainly on the cabinet width:

  • Vertical cable duct (100 × 111 mm, removable front) — for SZB IT 800 mm wide, fixed to the depth brace of the side panel. The closed solution for many cables.
  • Wire mesh cable tray (150 × 15 mm) — so shallow that it fits between the depth brace and the side panel in SZB IT 600 mm wide.
  • Sheet steel cable tray (150 × 30 mm) — sturdier, but in SZB IT 600 mm wide it can only be mounted on the inside of the depth brace.
  • PVC cable duct with C-profile — the economical variant, fixed to the depth braces; duct in 2 m sections, stiffening profile in cabinet height.
Vertical cable duct – 100 × 111 mm, for SZB IT 800 mm wide
Vertical cable duct100 × 111 mm, for SZB IT 800 mm wide
Wire mesh cable tray – 150 × 15 mm, galvanised steel
Wire mesh cable tray150 × 15 mm, galvanised steel

Vertical cable duct (100 × 111 mm, for SZB IT 800 mm wide)

Rack heightRAL 7035RAL 9005
42 UW-6186-22-03-011W-6186-22-03-161
45 UW-6186-22-02-011W-6186-22-02-161
47 UW-6186-22-01-011W-6186-22-01-161

Supplied with fixings, packaging unit 1 pc.

Wire mesh and sheet steel cable trays (width 150 mm, galvanised steel)

Tray lengthRack heightWire mesh cable tray (15 mm deep)Sheet steel cable tray (30 mm deep)
1100 mm24 UW-4755-25-08-000W-4755-20-08-000
1200 mm27–28 UW-4755-25-07-000W-4755-20-07-000
1300 mm30 UW-4755-25-06-000W-4755-20-06-000
1400 mm32–33 UW-4755-25-05-000W-4755-20-05-000
1600 mm36 UW-4755-25-04-000W-4755-20-04-000
1700 mm38–39 UW-4755-25-03-000W-4755-20-03-000
1800 mm40–42 UW-4755-25-02-000W-4755-20-02-000
2000 mm45–47 UW-4755-25-01-000W-4755-20-01-000

Fixed to the horizontal depth braces, supplied with fixings, packaging unit 1 pc.

PVC cable duct (2000 mm sections)

WidthDepthCatalogue number
60 mm100 mmM1O-02-1442
60 mm80 mmM1O-02-1438
40 mm60 mmM1O-02-1424
40 mm40 mmM1O-02-1428

Order duct and stiffening C-profile separately.

C-profile for stiffening the PVC duct (Aluzinc, with fixings)

Rack heightfor duct width 40 mmfor duct width 60 mm
15 UW-SB00-31-22-000W-SB00-31-10-000
18 UW-SB00-31-21-000W-SB00-31-09-000
21 UW-SB00-31-36-000W-SB00-31-30-000
24 UW-SB00-31-20-000W-SB00-31-08-000
27 UW-SB00-31-35-000W-SB00-31-29-000
28 UW-SB00-31-19-000W-SB00-31-07-000
30 UW-SB00-31-34-000W-SB00-31-28-000
32 UW-SB00-31-18-000W-SB00-31-06-000
33 UW-SB00-31-33-000W-SB00-31-27-000
36 UW-SB00-31-17-000W-SB00-31-05-000
38 UW-SB00-31-16-000W-SB00-31-04-000
39 UW-SB00-31-32-000W-SB00-31-26-000
40 UW-SB00-31-15-000W-SB00-31-03-000
42 UW-SB00-31-14-000W-SB00-31-02-000
45 UW-SB00-31-13-000W-SB00-31-01-000
47 UW-SB00-31-31-000W-SB00-31-25-000
Request with the enclosure →or individually for retrofitting

Frequently asked questions

Which vertical cable routing fits a 600 mm wide cabinet?

The wire mesh cable tray: at 15 mm deep it fits into the space between the depth brace and the side panel. The sheet steel cable tray (30 mm) can only be mounted there on the inside of the depth brace, and the vertical cable duct is intended for cabinets 800 mm wide.

Cable management panel with cable duct or with rings?

The cable duct with removable front looks tidy and protects the cables — good for installations that are rarely re-patched. Open rings are quicker when connections are changed often. The panel W-SB55 with steel rings is the flexible middle way: you choose the size and number of rings yourself.

Why brush panels instead of open cable openings?

Every open pass-through lets warm exhaust air flow back in front of the equipment. The brush seal surrounds the cables and keeps the gap closed — especially in cabinets with cold/hot aisle separation or in the Databox containment.

Does the cable management come fitted from the factory?

Yes — cable management panels, cable trays and vertical ducts can be ordered with the cabinet and are installed at the factory. For individual orders the catalogue number from the tables is enough.

All questions in the FAQ →

Putting together the cable management for your cabinet?

Tell us the cabinet series, width, height and number of ports — we will suggest the matching panels, rings and trays. Quotation within 2 working days at most.