Mounting system for electrical enclosures
Plate, rails, module system

Mounting plate with guides and supports, CLASSIC and UNI rail systems for the SZE2, mounting rails A, B and C for the SZE3, profile rails II with TS 35 DIN rail and the ZPAS module system – with lengths, key data and catalogue numbers.

Request a quote Configure electrical enclosure

Mounting plate, rail frame or module system?

The mounting plate is the simplest mounting level: a continuous galvanised surface, 3 mm thick, on which devices, cable ducts and DIN rails are screwed directly. Rail systems, by contrast, build a frame inside the enclosure – with levels at any depth and for higher loads. The module system is the special form for distribution boards: modular devices on DIN rails behind module panels that protect against contact.

Mounting plate, guides and supports

On both series the mounting plate is made of 3 mm galvanised sheet steel (normal sheet tolerances to EN 10143) and is supplied with the fixing elements for installation. On request ZPAS makes it powder-coated – in RAL 7035 or another colour –, as a swing-out version with hinges or from Textolite. The exact plate dimensions are shown in the dimensional drawings of the enclosures (SZE2: catalogue p. 17, SZE3: p. 69).

Guides (set of 2, fixed to the floor plate) make it easier to insert and align the plate. On the SZE3 the plate is positioned steplessly in the enclosure depth by means of guides and supports; if it is to sit at the rear between the vertical frame profiles, two additional supports are required.

Mounting plate – 3 mm sheet steel, galvanised
Mounting plate3 mm sheet steel, galvanised
Inserting the mounting plate – SZE2, plate over the full enclosure height
Inserting the mounting plateSZE2, plate over the full enclosure height
SZE3: guides and supports – plate steplessly adjustable in depth
SZE3: guides and supportsPlate steplessly adjustable in depth
SZE3 supports – set for right and left
SZE3 supportsSet for right and left

Mounting plate

Cabinet widthSZE2SZE3
Enclosure height 2000 mm
600 mmW-1951-67-10-000-BPW-6282-33-08-000
800 mmW-1951-67-07-000-BPW-6282-33-07-000
1000 mmW-1951-67-04-000-BPW-6282-33-06-000
1200 mmW-1951-67-01-000-BPW-6282-33-05-000
Enclosure height 2200 mm
600 mmW-4950-28-10-000-BPW-6282-33-04-000
800 mmW-4950-28-07-000-BPW-6282-33-03-000
1000 mmW-4950-28-04-000-BPW-6282-33-02-000
1200 mmW-4950-28-01-000-BPW-6282-33-01-000

Mounting plate guides (set of 2)

Rack depthSZE2SZE3
400 mmW-1951-64-04-000W-6282-35-04-000
500 mmW-1951-64-03-000W-6282-35-03-000
600 mmW-1951-64-02-000W-6282-35-02-000
800 mmW-1951-64-01-000W-6282-35-01-000

Mounting plate supports – SZE3 only

Mounting plate guides – set of 2, on the floor plate
Mounting plate guidesSet of 2, on the floor plate
SZE3: plate at the rear – between the vertical frame profiles, with supports
SZE3: plate at the rearBetween the vertical frame profiles, with supports
VersionPacking unitCatalogue number
Two supports (right and left) with fixing elements, for the plate at the rear between the vertical frame profiles1 setW-6282-36-00-000

Mounting plate: packing unit 1 pc., guides: 1 set. Guides and supports made of galvanised sheet steel, with fixing elements.

📄 Dimensional drawings in the catalogue: SZE2 p. 36 → · SZE3 p. 80–81 →

Mounting plate connector for the enclosure row

In bayed enclosures it joins the mounting plates into a continuous mounting level across the enclosure boundary – galvanised sheet steel, with fixing accessories.

SZE2 mounting plate connector – 1867 or 2067 × 86 × 30 mm
SZE2 mounting plate connector1867 or 2067 × 86 × 30 mm
SZE3 mounting plate connector – for 2000 and 2200 mm enclosure height
SZE3 mounting plate connectorFor 2000 and 2200 mm enclosure height
Rack heightSZE2: dimensions H × W × DSZE2SZE3
2000 mm1867 × 86 × 30 mmW-1951-47-01-000W-6282-24-02-000
2200 mm2067 × 86 × 30 mmW-4950-30-00-000W-6282-24-01-000

Packing unit 1 pc. Partition walls and baying accessories for the enclosure row can be found under Doors, panels, roof & plinths.

📄 Dimensional drawings in the catalogue: SZE2 p. 52 → · SZE3 p. 90 →
Request with the enclosure →Configure the complete enclosure: in the configurator → · Catalogue number: SZE3 · SZE2

CLASSIC and UNI rail systems for the SZE2

There are two rail systems for the SZE2, which use the same fixing sets and can be combined. CLASSIC works with supports: cross members are inserted into the horizontal or vertical perforations of the enclosure frame, vertical supports are fixed to the floor and roof plates; the CLASSIC mounting rails, available in 25 lengths from 200 to 1200 mm, sit on these supports. This allows mounting levels to be built at any position in the enclosure.

UNI is the universal profile: its perforation matches both the horizontal and the vertical perforations in the enclosure frame, and the standard lengths are matched to the height, width and depth of the enclosures – other lengths are cut to size on request. With the angle connector they form any kind of frame; UNI also carries the 19″ frame and the profile rails II of the module system. For the mounting rail frame of the SZE2 the catalogue states a load capacity of 1,600 kg (mounting plate: 1,000 kg).

Frame assembly CLASSIC (left) and UNI (right) – CLASSIC: 1 mounting rail, 2 cross member, 3 vertical support – UNI: 5 mounting rail, 6 angle connector; A–F = connection points according to catalogue p. 40
Frame assembly CLASSIC (left) and UNI (right)CLASSIC: 1 mounting rail, 2 cross member, 3 vertical support – UNI: 5 mounting rail, 6 angle connector; A–F = connection points according to catalogue p. 40
CLASSIC mounting rail – 25 lengths, 200–1200 mm
CLASSIC mounting rail25 lengths, 200–1200 mm
CLASSIC cross member – across the width or depth
CLASSIC cross memberAcross the width or depth
CLASSIC vertical support – on the floor and roof plates
CLASSIC vertical supportOn the floor and roof plates
UNI mounting rail – matches the frame perforation
UNI mounting railMatches the frame perforation

CLASSIC mounting rail

For fixing to cross members and vertical supports. Matched to the enclosure width: 550 mm (enclosure 600 mm), 750 mm (800), 950 mm (1000) and 1150 mm (1200).

LengthCatalogue numberLengthCatalogue number
200 mmW-0573-12-25-000650 mmW-0573-12-13-000
225 mmW-0573-12-24-000700 mmW-0573-12-12-000
250 mmW-0573-12-23-000750 mmW-0573-12-11-000
275 mmW-0573-12-22-000775 mmW-0573-12-10-000
300 mmW-0573-12-21-000800 mmW-0573-12-09-000
350 mmW-0573-12-20-000850 mmW-0573-12-08-000
400 mmW-0573-12-19-000900 mmW-0573-12-07-000
450 mmW-0573-12-18-000950 mmW-0573-12-06-000
500 mmW-0573-12-17-0001000 mmW-0573-12-05-000
525 mmW-0573-12-16-0001050 mmW-0573-12-04-000
550 mmW-0573-12-15-0001100 mmW-0573-12-03-000
600 mmW-0573-12-14-0001150 mmW-0573-12-02-000
––1200 mmW-0573-12-01-000

CLASSIC cross member

Fixed to the vertical or horizontal perforations in the enclosure frame.

Enclosure sizeSupport lengthCatalogue number
Installation across the width
600 mm552.5 mmW-1951-46-08-000
800 mm752.5 mmW-1951-46-07-000
1000 mm952.5 mmW-1951-46-06-000
1200 mm1152.5 mmW-1951-46-05-000
Installation across the depth
400 mm240 mmW-1951-46-04-000
500 mm340 mmW-1951-46-03-000
600 mm440 mmW-1951-46-02-000
800 mm640 mmW-1951-46-01-000

CLASSIC vertical support

For fixing to the floor and roof plates of the enclosure frame – according to the catalogue either indirectly via UNI mounting rails (W-1951-19-05-000 to W-1951-19-08-000), directly on the roof or floor plate, or directly on the vertical profiles of the enclosure frame.

Rack heightSupport lengthCatalogue number
2000 mm1875 mmW-1951-48-01-000
2200 mm2075 mmW-1951-48-05-000

mounting rail UNI

Standard lengths according to enclosure size; other lengths on customer request, also cut to size individually.

Enclosure sizeRail lengthCatalogue number
Vertical – for enclosure height
1200 mm1075 mmW-1951-19-04-000
1600 mm1475 mmW-1951-19-03-000
1800 mm1675 mmW-1951-19-02-000
2000 mm1875 mmW-1951-19-01-000
2200 mm2075 mmW-4950-31-00-000
Horizontal across the width – for enclosure width
600 mm562.5 mmW-1951-19-08-000
800 mm762.5 mmW-1951-19-07-000
1000 mm962.5 mmW-1951-19-06-000
1200 mm1162.5 mmW-1951-19-05-000
Horizontal across the depth – for enclosure depth
400 mm300 mmW-1951-19-12-000
500 mm400 mmW-1951-19-11-000
600 mm500 mmW-1951-19-10-000
800 mm700 mmW-1951-19-09-000

Angle connectors for UNI mounting rails

UNI angle connector – joins UNI mounting rails to form a frame
UNI angle connectorJoins UNI mounting rails to form a frame
VersionPacking unitCatalogue number
Connector for UNI mounting rails, galvanised, without fixing accessories1 pc.W-1951-21-00-000

All rails and supports made of galvanised sheet steel, supplied without fixing accessories (see fixing accessories), packing unit 1 pc.

Request with the enclosure →or individually for retrofitting

Fixing accessories: thread-forming screws and cage nuts

CLASSIC, UNI and the SZE3 mounting rails are screwed together with the same sets of 20 pieces. The thread-forming screw M6 × 16 (W-1951-44-01-000) connects the mounting rails to the enclosure frame and to each other. Depending on the connection point, the catalogue alternatively provides for a screw M6 × 16 with cage nut M6 or with nut M6 and washers – the overview on catalogue page 40 shows which point is screwed in which way. For the SZE3 there are also cage nuts M8 with wing tabs, with which devices are fixed directly to the enclosure frame.

Thread-forming screw M6 × 16 – set of 20 pcs
Thread-forming screw M6 × 16Set of 20 pcs
Screw with cage nut M6 – set of 20 pcs
Screw with cage nut M6Set of 20 pcs
Screw with nut M6 – set of 20 pcs
Screw with nut M6Set of 20 pcs
Cage nut M8 with wing tabs – SZE3, set of 10 pcs
Cage nut M8 with wing tabsSZE3, set of 10 pcs
setContentsPacking unitCatalogue number
Thread-forming screwScrew M6 × 16 – 20 pcs1 setW-1951-44-01-000
Screw with cage nutScrew M6 × 16, cage nut M6, washer 6.4 – 20 pcs each1 setW-1951-44-02-000
Screw with nutScrew M6 × 16 – 20 pcs, nut M6 – 20 pcs, washer 6.4 – 40 pcs1 setW-1951-44-03-000
Cage nut M8 (SZE3)Cage nut M8 with wing tabs – 10 pcs1 setW-M1F-03-0165-000

Sets W-1951-44-01-000 and W-1951-44-02-000 apply to the SZE2 and SZE3. The mounting set for profile rails II and 19″ profile rails is listed under profile rails II.

📄 Dimensional drawings in the catalogue: SZE2 p. 40 → · SZE2 p. 43 → · SZE3 p. 86 →
Request with the enclosure →or individually for retrofitting

Mounting rails A, B and C for the SZE3

The SZE3 frame is perforated on two levels in a 25 mm grid – with Ø 5.4 mm openings for thread-forming screws M6 and 10.5 × 16.5 mm openings for cage nuts M8 with wing tabs. The mounting rails are matched to this: type A and type B build frames inside the enclosure and differ in the way they are fixed; with thread-forming screws M6 they can also be connected to each other. Mounting rail C fixes the 19″ profile rails to the enclosure frame.

Mounting rail type A – SZE3, 262–1162 mm
Mounting rail type ASZE3, 262–1162 mm
Mounting rail type B – SZE3, 206–1106 mm
Mounting rail type BSZE3, 206–1106 mm
Example frames – made of mounting rails type A and type B
Example framesMade of mounting rails type A and type B
Mounting rail C – for 19″ profile rails
Mounting rail CFor 19″ profile rails

Mounting rails type A and type B

Enclosure width or depth*Type A: lengthType AType B: lengthType B
–262 mmW-6282-40-10-000206 mmW-6282-42-10-000
400 mm362 mmW-6282-40-09-000306 mmW-6282-42-09-000
500 mm462 mmW-6282-40-08-000406 mmW-6282-42-08-000
600 mm562 mmW-6282-40-07-000506 mmW-6282-42-07-000
–662 mmW-6282-40-06-000606 mmW-6282-42-06-000
800 mm762 mmW-6282-40-05-000706 mmW-6282-42-05-000
–862 mmW-6282-40-04-000806 mmW-6282-42-04-000
1000 mm962 mmW-6282-40-03-000906 mmW-6282-42-03-000
–1062 mmW-6282-40-02-0001006 mmW-6282-42-02-000
1200 mm1162 mmW-6282-40-01-0001106 mmW-6282-42-01-000

* for horizontal fixing between the posts of the enclosure frame; “–” = length without an assigned enclosure size. Galvanised sheet steel, without fixing accessories, packing unit 1 pc.

Mounting rail C – for the 19″ frame

Carries the 19″ profile rails in the SZE3; in 800 mm wide enclosures, additional brackets (W-5205-90-00-C12) establish the 19″ dimension. Profile rails and cross members are listed under 19″ accessories.

Enclosure width or depthLengthCatalogue number
400 mm306 mmW-6282-43-06-000
500 mm406 mmW-6282-43-05-000
600 mm506 mmW-6282-43-04-000
800 mm706 mmW-6282-43-03-000
1000 mm906 mmW-6282-43-02-000
1200 mm1106 mmW-6282-43-01-000

Galvanised sheet steel, without fixing accessories, packing unit 1 pc.

📄 Dimensional drawings in the catalogue: p. 84 → · p. 86–87 →
Request with the enclosure →or individually for retrofitting

Profile rails II and TS 35 DIN rail

Profile rails II form the frame for modular devices in the SZE2: mounting brackets, 35 mm DIN rails and module panels are fitted to them. They sit on four UNI mounting rails whose length matches the enclosure depth – so the depth of the level can be adjusted steplessly. A mounting set fixes one pair of profile rails II (or 19″ profile rails) to the UNI rails.

The TS 35 DIN rail (15 mm deep, galvanised) is fitted to the profile rails II with two mounting brackets. For equipment that places heavy loads on the rails, the catalogue provides other constructions in 1000 and 1200 mm wide enclosures – we will advise you on this in your project.

Profile rails II – pair, for 12 or 14 DIN rails
Profile rails IIPair, for 12 or 14 DIN rails
Mounting set – for one pair of profile rails
Mounting setFor one pair of profile rails
TS 35 DIN rail – 15 mm deep, 600–1200 mm
TS 35 DIN rail15 mm deep, 600–1200 mm
Mounting bracket – two per DIN rail
Mounting bracketTwo per DIN rail

Profile rails II

Rack heightCapacity*Packing unitCatalogue number
2000 mm12 DIN rails2 pcsW-4881-67-02-000
2200 mm14 DIN rails2 pcsW-4881-67-04-000

* maximum number of installed 35 mm DIN rails. Galvanised sheet steel, without mounting elements.

Mounting set for profile rails II and 19″ profile rails

ContentsPacking unitCatalogue number
Screw M6 × 16 – 4 pcs, nut M6 – 4 pcs, washer – 8 pcs, toothed lock washer – 4 pcs (for one pair of rails on UNI mounting rails)1 setW-SB00-37-04-000

TS 35 DIN rail and mounting brackets

VersionFor enclosure widthCatalogue number
TS 35 DIN rail600 mmW-0573-52-24-000
TS 35 DIN rail800 mmW-0573-52-23-000
TS 35 DIN rail1000 mmW-0573-52-22-000
TS 35 DIN rail1200 mmW-0573-52-21-000
Mounting bracket (1 pc.)allW-0573-52-30-000

DIN rail without mounting elements, packing unit 1 pc. Mounting brackets galvanised, with elements for fitting to profile rail II and DIN rail; 2 brackets are required per rail.

Request with the enclosure →Configure the complete enclosure: in the configurator → · Catalogue number: SZE3 · SZE2

ZPAS module system for distribution boards in the SZE2

The module system turns the SZE2 into a distribution board: the modular devices sit on DIN rails, with module panels 150 mm high in front of them, fixed directly to the profile rails II. Installations in this version have the degree of protection IP 30 against contact with live parts, the closed SZE2 IP 54.

Planning is done in field-height modules (MFH), 1 MFH = 150 mm. An installation with a busbar system generally has three zones: busbars (3 MFH), device mounting (8 MFH in the 2000 mm high enclosure) and cable entry (1 MFH + 100 mm). A 2000 mm high enclosure therefore takes 288 modules of 18 mm at 600 mm width, 432 at 800 mm and 576 at 1000 and 1200 mm.

Remaining areas are closed by blank module plates 150, 100 and 50 mm; depending on the enclosure height, a plate of a different height is required – 50 mm in the 1800 mm high enclosure, 100 mm in the 2000 mm high enclosure. Cover strips conceal the vertical and horizontal gaps between profile rails II and the enclosure frame. Panels, blank plates and cover strips are powder-coated in RAL 7035. For electricity meters there is a meter tray for mounting on profile rails II.

Module system in the SZE2 – module panels in front of the modular devices
Module system in the SZE2Module panels in front of the modular devices
Assembly – 1 profile rail II, 2 UNI mounting rail, 4 DIN rail, 5 mounting bracket, 6 module panel, 7 blank plate, 8 cover strips
Assembly1 profile rail II, 2 UNI mounting rail, 4 DIN rail, 5 mounting bracket, 6 module panel, 7 blank plate, 8 cover strips
Module panel 150 – 24 to 48 modules type S
Module panel 15024 to 48 modules type S
Blank module plate – 150, 100 or 50 mm high
Blank module plate150, 100 or 50 mm high
Cover strips – vertical and horizontal
Cover stripsVertical and horizontal

Module panel 150

Cabinet widthCapacity (modules type S, 18 mm)Catalogue number
600 mm24W-4881-68-01-011
800 mm36W-4881-68-02-011
1000 mm48W-4881-68-03-011
1200 mm48W-4881-68-04-011

Blank module plates

Cabinet widthHeight 150 mmHeight 100 mmHeight 50 mm
600 mmW-4881-68-05-011W-4881-71-01-011W-4881-72-01-011
800 mmW-4881-68-06-011W-4881-71-02-011W-4881-72-02-011
1000 mmW-4881-68-07-011W-4881-71-03-011W-4881-72-03-011
1200 mmW-4881-68-08-011W-4881-71-04-011W-4881-72-04-011

Cover strips

VersionFor enclosureCatalogue number
Vertical cover stripsHeight 2000 mmW-4881-69-02-011
Vertical cover stripsHeight 2200 mmW-4881-69-04-011
Horizontal cover stripsWidth 600 mmW-4881-70-01-011
Horizontal cover stripsWidth 800 mmW-4881-70-02-011
Horizontal cover stripsWidth 1000 mmW-4881-70-03-011
Horizontal cover stripsWidth 1200 mmW-4881-70-04-011

Module panels and blank plates with mounting elements, packing unit 1 pc. Cover strips: according to the current catalogue one set of two vertical or two horizontal strips with mounting elements.

Request with the enclosure →or individually for retrofitting

Equipment shelves for the SZE2

For devices that stand rather than hang: the equipment shelves are fixed directly to the enclosure frame, are powder-coated in RAL 7035 and carry 100 kg – the 754 × 390 mm shelf for 800 × 500 mm enclosures carries 200 kg. According to the catalogue, ZPAS makes other dimensions on request.

Equipment shelves – smooth or perforated, RAL 7035
Equipment shelvesSmooth or perforated, RAL 7035
Cabinet widthRack depthDimensionsLoad capacityPerforatedCatalogue number
600 mm600 mm552 × 540 × 25 mm100 kgnoW-5899-09-00-011
800 mm600 mm752 × 530 × 25 mm100 kgyesW-5899-11-00-011
800 mm500 mm754 × 390 × 33 mm200 kgnoW-8041-A1-67-011
600 mm800 mm552 × 730 × 25 mm100 kgyesW-6138-61-00-011
800 mm800 mm752 × 730 × 25 mm100 kgyesW-6412-62-00-011

Load capacity according to the catalogue. Supplied with fixing accessories, packing unit 1 pc. For 19″ devices there are separate 19″ equipment shelves.

Request with the enclosure →or individually for retrofitting

Frequently asked questions

CLASSIC or UNI – what is the difference?

CLASSIC is built on supports: cross members and vertical supports are fixed to the enclosure frame or to the floor and roof plates, and the CLASSIC mounting rails, available in 25 lengths from 200 to 1200 mm, sit on them. UNI is a universal profile whose perforation matches the perforations in the enclosure frame; with angle connectors it forms any kind of frame, including the 19″ frame and the substructure of the module system. Both systems use the same fixing sets and can be combined.

Mounting plate or rail frame – which carries more?

For the SZE2 the catalogue gives 1,000 kg for the mounting plate and 1,600 kg for the mounting rail frame. The mounting plate is a closed surface for devices, ducts and DIN rails and is part of the standard delivery; a rail frame creates mounting levels at any depth.

Do the SZE2 rails also fit the SZE3?

No. The SZE3 has its own 25 mm grid on two levels; for this there are type A and B mounting rails for frames and type C for the 19″ frame. The same are the fixing sets with thread-forming screws M6 × 16 or cage nuts M6, as well as the 19″ profile rails, brackets and cross members.

When is the module system worthwhile?

When a distribution board with many modular devices is built in the SZE2: the devices sit on DIN rails behind module panels, with protection against contact to IP 30. A 2000 mm high enclosure takes 288 modules of 18 mm at 600 mm width, 432 at 800 mm and 576 at 1000 and 1200 mm.

Are rails and shelves available in special lengths?

Yes. UNI mounting rails are supplied in other lengths on request or cut to size individually, and ZPAS also manufactures equipment shelves in other dimensions on request. State the enclosure size and the length you need in your enquiry – or request the complete frame.

All questions in the FAQ →

Mounting system put together?

Send us catalogue numbers and quantities – or the enclosure size and a list of devices, and we will put the frame together. Quotation within 2 working days at most.